AUGER & TRAY ADJUSTMENTS

  

By retiming the vend spring and/or adding product pushers, difficult sized vend items can be dispensed more dependably. By altering tray spacing, larger items can be vended. By changing the tray configuration, different product mixes can be accommodated.

TRAY SPACING
The snack machine trays can be adjusted up or down in one inch increments to provide additional headroom for vending taller products. When increasing the height in one area, the same amount of room will be lost at the snack tray above or below the one being adjusted.

REMOVING A SNACK TRAY
1. Pull out the snack machine tray to be removed until it stops.
2. Disconnect the candy tray harness and undo any clamps. See Figure 3 (Al 0075).
3. On the 12 selection snack machine- remove harness from slot in right side wall and disconnect harness plug. 19 & 35 Selection- disconnect the main harness from the tray plug.
4. Lift up on the front of the tray and pull slightly forward approximately 1/2 inch (1.5 cm) to clear tray stop.
5. Lift up on the rear of the tray and remove it from the snack vending machine.  

REINSTALLING A TRAY
1. 12 selection snack machine - - Place the back of the tray on the rails and lift up to clear the tray stops. 19 & 35 selection snack vendor -- Place the back of the tray on the rails by placing its rear rollers on the left and right rails and lifting up on the front of the tray as you push it back.
2. Slide tray into snack machine until it stops, lift up slightly on front of tray and push in to lock into detent position.
3. 12 selection snack machine - - Connect harness plug. Install harness tubing into slot in right-side wall. 19 & 35 selection snack vendor - Connect the main harness to the tray plug. Re-clamp the main harness if necessary.
4. Test vend the tray to assure that the tray plug is properly seated and all motors are working.

PRODUCT PUSHERS
Order product pushers p/n 4025748. Snaps on to end of auger. See Figure 3. Test

vend and adjust if necessary. PRODUCT PUSHER PIN 4025748.

VEND SPRING TIMING
The shape, size and thickness of product affects how well it falls off the tray. Most items can be vended successfully when the spring end is positioned at the 6 oclock position. If vending problems occur with coil ends at the standard 6 oclock position, adjust the drop off either with product pushers or by retiming the spring.
I2 SELECTION AUGER RETIMING
1. Remove the tray from the snack vendor as previously described.
2. Remove the two screws from the top of the motor assembly. See Figure 4a.
3. Lift up slightly on the motor assembly.
4. Pull the vend spring away from the motor until the auger hug separates from the motor shaft.
5. Rotate the spring to the desired position and reinsert the hub into the motor.
6. Slide the motor assembly down, locating the tabs in the slots in the bottom of the tray. Be sure the rib in the tray is locked to the tabs of the spring coupling.
7. Reinsert the two screws into the top of the motor assembly. See Figure 4a.
8. Replace the tray in the vendor.

GFI9 & GF35 AUGER RETIMING GFI9 and GF35 can only be retimed to 12 o'clock (factory set at 6 o'clock) - only useful for very wide products. Use product pushers to retime end of auger.
1. Remove the tray from the snack vending machine.
2. Pull hair pin clip holding vend spring to motor hub.
3. Rotate spring 180° degrees.
4. Replace hair pin clip through the vend spring and the motor hub.
5. Replace tray in the snack machine.

CHANGE TRAY CONFIGURATION

12 Selection Snack Machine - Order the desired product spring. See the Parts Ordering section of this manual.
1. Remove tray from the machine.
2. Remove motor assembly as described in Retiming 12 selection. See Figure 4a.
3. Remove product spring/ auger.
4. If necessary, remove motors from motor assembly. Retain the screws.
5. Move the dividers as necessary.
6. Move snack motors if necessary.
7. Insert product spring known as an augers.
8. Replace vend motor assembly as described in Retiming 12 selection snack machine.
9. Replace snack tray in the vending machine.
10. Test vend new configuration.
19 & 35 Selection- Product spring /Augers cannot be changed but Snack and Candy trays are interchangeable. Order the desired trays from the Parts Department. See the Parts Ordering section of this manual.

To change from one tray type to the other, the tray side rails must be moved forward or back in slots in side walls.
1. Remove the tray from the snack vending machine.
2. Unscrew the screw holding the tray rail to the side wall.
3. Slide the rail forward (for a snack tray) or back (for a candy tray).
4. Install the screw to hold the rail in place.
5. Install the replacement tray in the vending machine.
6. Attach the main harness to the candy tray plug. Al 00 89
7. Test the candy vending machine.